Anode Winding Machine hmanga siam a ni

He fully automatic cylindrical cell winding machine hi thil tum pakhat atan engineer a ni a, chu chu pre-fabricated, tabbed electrode jigsaws leh separator materials te chu perfect, isolated jelly rolls ah a chantir a ni. Anode winding machne chauh ni lovin, pre-notched electrode webs (tabs welded tawh) leh separator films pahnih precision unwinding chu expert takin a handle a ni. Machine lungphum chu a three{4}}stage automatic edge guide correction system-unwind correction, process correction, leh entry-point correction-a ni a, chu chuan material zawng zawng chu mandrel-a an inzawm khawm rualin flawless alignment a tichiang a ni. Winding process hi a sei zawng dik tak atan color mark sensor hmanga control a ni a, integrated short-circuit detection system chuan core chu real-time-ah a enkawl thung. Automatic taping hian final layer chu a secure a ni. Output hi ready-to-assemble cylindrical core a ni a, exceptional consistency nena siam chhuah a ni a, jelly-roll short-circuit testing function nei a ni.

Model: SZO-W2670 a ni

A chiang zawk

1. Material specification hrang hrang

2. Winding hman dan

Pathum-reel needle pathum-station winding.
Needle diameter Ø3.5(a nih loh leh customer-in a tarlan size Ø3.0-Ø5.0)
Pole beng awm zat: positive 1 leh negative 1
Pole ear exposure: Diaphragm part atanga 8-25mm a hlaah a awm
Positive leh negative pole ears hi battery cell sir lehlamah a awm a
Winding diameter 13mm (?) aia tlem emaw a tlukpui emaw 32mm aia tlem emaw a tlukpui emaw

3. Machine pumpui debug leh model thlak nan hian 2-3H vel a ngai.

4. Winding dikna: 1.1.
1, positive leh negative plate alignment: ±0.3mm
2, positive leh negative plate leh diaphragm alignment: ±0.3mm
3, diaphragm alignment layer hnih: ±0.3mm

5.Winding theihna: 1.1.
1. Thil siam chhuah theihna
Thil siam chhuah chakna 22-25PPM900mm pole
2, operation rate 95% aia tam emaw, a tlukpui emaw a ni.
Operation rate ={total production/(boot hun - mamawh deduction hun) × hmanrua theoretical production speed}×100%,
Deduction hun tul: -equipment ni lo avanga downtime, refueling, taping leh production buatsaih hun dang. 3, pass rate 98% aia tam emaw, a tlukpui emaw
Product tha rate =【 Product tha zawng zawng/(production zawng zawng - deduction mamawh zat) 】×100% (bad material factors tih loh chu)
A zat tihtlem a ngai, thil chhia avanga lo awm, non-equipment factors, tape \\ha lo, film sei \\ha lo, beng \\ha lo, etc. te.
Positive leh negative plate tension: 20N a inthlak theih (adjust theih) Diaphragm tension: 10N a inthlak theih (adjust theih)

Thil hmanrua technical parameters te chu:
1, power supply: pakhat-phase AC220V±10% 50Hz
2, supply air source: 0.5-0.7MPa (0.5MPa gas supply, a flow rate mamawh chu 300NL/min) a ni.
3, boruak hman dan (JISB3502 angin) ambient temperature hman dan: 0-55℃drying room
Etch gas emaw, kang thei boruak emaw, leivut boruak tha lo emaw a awm tur a ni lo
4, dimensions: a sei zawng 2500mm× a san zawng 2000mm× a zau zawng 1800mm (a size tak tak chu design hnuhnung ber a zirin a ni)
5, a lan dan rawng: computer var + orange (a nih loh leh customer-in a ruat rawng, rawng palette pe rawh)
6, a rih zawng: 2500Kg aia tlem
7, chakna: 12Kw
8, ri: 75db aia tlem emaw a tlukpui emaw (suction fan tel lovin)

9. Thil hmanrua diagram: 1.1.

10, Emachine material mamawh chungchangah quipment: 1.1.

1, positive leh negative electrode plate a ni

Pole slices zau taka slitting theihna tur tolerances

1.1 Electrode coating a zau zawng lam hawia thickness deviation

1.1 Waveform, bending leh warping

Waveform awm lo (finger surface defects), warping 0.2/500mm (pole piece curling hnua parts cut off), snake bending error: pole piece unit sei zawnga snake bending error chu 1mm/1m aia tlem emaw, a tlukpui emaw a ni.

2. Diaphragm (Diaphragm) a ni

2.1 Slitting zau zawng tolerance: ±0.05mm chhungah

2.2 Waveform, bending, leh skirt shape te hi thil chhia te hmuh theiha ngaihtuah theih loh a ni

Thil hmanraw pawimawh ber ber configuration

Random accessories te pawh a awm bawk